Appalachian Blacksmiths Association list of in the US Books:.Dictionary from for those hard to google terms.Have an englishweight anvil? Try this nifty little tool from to find out how much it weighs in lbs.- a suggested program of study to learn hand forging.
#Hay budden anvil serial numbers mods
Any NSFW posts will be reviewed by the mods and may be removed based on our judgement of the value of the content.When reporting content, you MUST state WHY you reported it.Blatant advertising and for sale posts are not allowed.Obviously this sub is for blacksmithing related topics, so keep posts related to blacksmithing.Blatant troll posts/comments will be removed. Please be considerate to others when posting/commenting.Read before attempting any kind of forging. Read our and, And be sure to check out below. My personal thinking is an anvil can be capped by using T1 plate and brass to bond the cap plate to gtunes musicapp base, although I've never tried it. Here is my anvil and one of my leg vises.
#Hay budden anvil serial numbers serial numbers
I sometimes come off as an hay budden serial numbers snob,' sorry. History and information pertaining to the American made Hay Budden Anvil. There's an Hay Burden 128 pound anvil to. I won't even pretend to know anything about anvils, but I'm sure somebody here might be able to help me. As I wrote you earlier I believed this anvil to be a Hay-Budden. Weight it is probably this lot number) Another sign of the Hay-Budden is. These number range from two to three digits in random ordering.Īlso note some times letters were stamped in after the serial numbers and/or on end of feet such as 'BB', 'SS' and possible other combinations.Anvil Identification. Hay-Budden also added numbers on the opposite side of the anvil from the trademark side up in the tapered area of the Heel. A handling hole being located in the base center (underside) and the other handling hole located under Horn in waist. These anvils have only two handling holes. The edge of the base (underside) is wider with 1 to 1 ½ inches width. These later made anvils can have a base cavity reaching 2 inches deep. The waist area was now narrow and nearly straight with this change in the manufacturing process using blocking dies to form the two pieces. There is no Top Plate line or seam to be seen or identified.The base remained forged from wrought iron or low carbon steel. Hay-Budden changed the manufacturing process during this last period and started successfully producing “Plate-less Anvils” (no top plate) making the entire “Upper” half (top and body) from one piece of forged steel. I would like to say that most of the anvils I have seen in the later years of production have the large Hay-Budden trademark and few retailer names applied. The anvils made by Hay-Budden during this last period contained all the prior described markings. The Hay-Budden stamp may also be small fitting within 4 to 5 inches. The Hay-Budden anvils made during this time may only contain a retailer’s name and weight stamp or both a retailer’s name and Hay-Budden trademark stamp sometimes overlapping with weight stamped in below. These are single digit in the range of 0 to 9 but consistent in size and Font on all the Hay-Budden anvils I have seen to date. No other manufactures of anvils is known to apply a number in this location. If no other marks can be found or determined on a anvil but a number is found marked near handling hole under horn THIS INDICATES it to be a Hay-Budden made anvil. In addition, some anvils may have a number(s) stamped on both sides of the handling hole. The number(s) can also be upsde down on some anvils. In the book, “Anvils in America”, 'These early Hay-Budden anvils have three handling holes (square holes actually) with one in the bottom of base (underneath), under Horn in middle of the waist and one under Heel (smaller of the other holes) in the middle of the waist.' The majority of these anvils will also be marked with a number stamped under the Horn and either on the left or right side of the handling hole. These two already joined pieces were then forge welded to the Lower Body or Base to complete the anvil. The “Top Plate” or “Faceplate” forge welded to Upper Body usually a distinctive visible line is present ½ to ⅝ below the Top Plate surface (depending on size of anvil) where they were joined. 1880 Hay-Budden anvil was made of three pieces.